Get The Important Preparation Guide With NSE6_FWF-6.4 Dumps
Get Totally Free Updates on NSE6_FWF-6.4 Dumps PDF Questions
NEW QUESTION 18
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP measurements can be scheduled to occur at specific times.
- B. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- C. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- D. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
Answer: B,C
Explanation:
DARRP (Distributed Automatic Radio Resource Provisioning) technology ensures the wireless infrastructure is always optimized to deliver maximum performance. Fortinet APs enabled with this advanced feature continuously monitor the RF environment for interference, noise and signals from neighboring APs, enabling the FortiGate WLAN Controller to determine the optimal RF power levels for each AP on the network. When a new AP is provisioned, DARRP also ensures that it chooses the optimal channel, without administrator intervention.
NEW QUESTION 19
Refer to the exhibit.
If the signal is set to -68 dB on the FortiPlanner site survey reading, which statement is correct regarding the coverage area?
- A. Areas with the signal strength equal to -68 dB are zoomed in to provide better visibility
- B. Areas with the signal strength weaker than -68 dB are cut out of the map
- C. Areas with the signal strength weaker than -68 dB are highlighted in orange and red to indicate that no signal was propagated by the APs.
- D. Areas with the signal strength equal or stronger than -68 dB are highlighted in multicolor
Answer: D
NEW QUESTION 20
When configuring Auto TX Power control on an AP radio, which two statements best describe how the radio responds? (Choose two.)
- A. When the AP detects any interference from a trusted neighboring AP stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- B. When the AP detects any other wireless signal stronger that -70 dBm, it will reduce its transmission power until it reaches the minimum configured TX power limit.
- C. When the AP detects PF Interference from an unknown source such as a cordless phone with a signal stronger that -70 dBm, it will increase its transmission power until it reaches the maximum configured TX power limit.
- D. When the AP detects any wireless client signal weaker than -70 dBm, it will reduce its transmission power until it reaches the maximum configured TX power limit.
Answer: B,D
NEW QUESTION 21
What type of design model does FortiPlanner use in wireless design project?
- A. Architectural model
- B. Integration model
- C. Analytical model
- D. Predictive model
Answer: A
Explanation:
FortiPlanner will look familiar to anyone who has used architectural or home design software.
NEW QUESTION 22
When enabling security fabric on the FortiGate interface to manage FortiAPs, which two types of communication channels are established between FortiGate and FortiAPs? (Choose two.)
- A. Security channels
- B. Control channels
- C. Data channels
- D. FortLink channels
Answer: B,C
Explanation:
The control channel for managing traffic, which is always encrypted by DTLS. l The data channel for carrying client data packets.
NEW QUESTION 23
Part of the location service registration process is to link FortiAPs in FortiPresence.
Which two management services can configure the discovered AP registration information from the FortiPresence cloud? (Choose two.)
- A. AP Manager
- B. FortiGate
- C. FortiAP Cloud
- D. FortiSwitch
Answer: B,C
Explanation:
FortiGate, FortiCloud wireless access points (send visitor data in the form of station reports directly to FortiPresence)
NEW QUESTION 24
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that cannot be used because of regulatory channel restrictions
- B. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- C. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
- D. Indicates channels that can be used only when Radio Resource Provisioning is enabled
Answer: B
NEW QUESTION 25
Refer to the exhibits.
Exhibit A
Exhibit B
The exhibits show the diagnose debug log of a station connection taken on the controller CLI.
Which security mode is used by the wireless connection?
- A. WPA3 Enterprise
- B. WPA2 Enterprise
- C. WPA2 Personal and radius MAC filtering
- D. Open, with radius MAC filtering
Answer: C
NEW QUESTION 26
Which of the following is a requirement to generate analytic reports using on-site FortiPresence deployment?
- A. Two wireless APs must be sending data
- B. SQL services must be running
- C. Wireless network security must be set to open
- D. DTLS encryption on wireless traffic must be turned off
Answer: B
NEW QUESTION 27
Which administrative access method must be enabled on a FortiGate interface to allow APs to connect and function?
- A. Security Fabric
- B. FortiTelemetry
- C. HTTPS
- D. SSH
Answer: A
NEW QUESTION 28
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the AP CLI, using the cw_diag -d sta command
- B. On the AP CLI, using the cw_diag ksta command
- C. On the controller CLI, using the diag wireless-controller wlac -d sta command
- D. On the controller CLI, using the WiFi Client monitor
Answer: C
NEW QUESTION 29
Refer to the exhibits.
Exhibit A
Exhibit B
A wireless network has been created to support a group of users in a specific area of a building. The wireless network is configured but users are unable to connect to it. The exhibits show the relevant controller configuration for the APs and the wireless network.
Which two configuration changes will resolve the issue? (Choose two.)
- A. Disable intra-vap-privacy for the Authors vap-wireless network
- B. Increase the transmission power of the AP radio interfaces
- C. For both interfaces in the wtp-profile, configure vap-all to be manual
- D. For both interfaces in the wtp-profile, configure set vaps to be "Authors"
Answer: A,C
NEW QUESTION 30
Which two configurations are compatible for Wireless Single Sign-On (WSSO)? (Choose two.)
- A. A VAP configured for WPA2 or 3 Enterprise
- B. A VAP configured to authenticate using a radius server
- C. A VAP configured to authenticate locally on FortiGate
- D. A VAP configured for captive portal authentication
Answer: A,B
Explanation:
In the SSID choose WPA2-Enterprise authentication.
WSSO is RADIUS-based authentication that passes the user's user group memberships to the FortiGate.
NEW QUESTION 31
Refer to the exhibit.
What does the asterisk (*) symbol beside the channel mean?
- A. Indicates channels that can be used only when Radio Resource Provisioning is enabled
- B. Indicates channels that cannot be used because of regulatory channel restrictions
- C. Indicates channels that are subject to dynamic frequency selection (DFS) regulations
- D. Indicates channels that will be scanned by the Wireless Intrusion Detection System (WIDS)
Answer: A
NEW QUESTION 32
When deploying a wireless network that is authenticated using EAP PEAP, which two configurations are required? (Choose two.)
- A. A WPA2 or WPA3 Enterprise wireless network
- B. An X.509 to authenticate the authentication server
- C. A WPA2 or WPA3 personal wireless network
- D. An X.509 certificate to authenticate the client
Answer: A,B
NEW QUESTION 33
Refer to the exhibits.
Exhibit A
Exhibit B
Exhibit C
A wireless network has been installed in a small office building and is being used by a business to connect its wireless clients. The network is used for multiple purposes, including corporate access, guest access, and connecting point-of-sale and IoT devices.
Users connecting to the guest network located in the reception area are reporting slow performance. The network administrator is reviewing the information shown in the exhibits as part of the ongoing investigation of the problem. They show the profile used for the AP and the controller RF analysis output together with a screenshot of the GUI showing a summary of the AP and its neighboring APs.
To improve performance for the users connecting to the guest network in this area, which configuration change is most likely to improve performance?
- A. Reduce the number of wireless networks being broadcast by the AP
- B. Enable frequency handoff on the AP to band steer clients
- C. Install another AP in the reception area to improve available bandwidth
- D. Increase the transmission power of the AP radios
Answer: D
NEW QUESTION 34
Where in the controller interface can you find a wireless client's upstream and downstream link rates?
- A. On the AP CLI, using the cw_diag ksta command
- B. On the AP CLI, using the cw_diag -d sta command
- C. On the controller CLI, using the diag wireless-controller wlac -d sta command
- D. On the controller CLI, using the WiFi Client monitor
Answer: A
NEW QUESTION 35
Which two statements about distributed automatic radio resource provisioning (DARRP) are correct? (Choose two.)
- A. DARRP requires that wireless intrusion detection (WIDS) be enabled to detect neighboring devices.
- B. DARRP measurements can be scheduled to occur at specific times.
- C. DARRP performs continuous spectrum analysis to detect sources of interference. It uses this information to allow the AP to select the optimum channel.
- D. DARRP performs measurements of the number of BSSIDs and their signal strength (RSSI). The controller then uses this information to select the optimum channel for the AP.
Answer: B,D
Explanation:
According to Fortinet training: "When using DARRP, the AP selects the best channel available to use based on the scan results of BSSID/receive signal strength (RSSI) to AC" and "To set the running time for DARRP optimization, use the following CLI command within the wireless controller setting: set darrp-optimize {integer}. Note that DARRP doesn't do continuous spectrum analysis..."
NEW QUESTION 36
Which statement is correct about security profiles on FortiAP devices?
- A. Security profiles on FortiAP devices can use FortiGate subscription to inspect the traffic
- B. FortiGate performs inspection the wireless traffic
- C. Disable DTLS on FortiAP
- D. Only bridge mode SSIDs can apply the security profiles
Answer: D
NEW QUESTION 37
......
Prepare With Top Rated High-quality NSE6_FWF-6.4 Dumps For Success in Exam: https://passguide.prep4pass.com/NSE6_FWF-6.4_exam-braindumps.html
